The following lines were added (+) and removed (-):
On a positive note, the sv4000 has a good strong CPU making it responsive to remote commands. It also has a pleasant user interface and some additional setup options missing from other low-end receivers. Perhaps one of the best features is the ability to flash the unit using a USB Thumbdrive, eliminating the need to connect the unit to a PC with a legacy serial cable.</big>On a positive note, the sv4000 has a fast, powerful CPU making it responsive to remote commands. It also has a pleasant user interface and some additional setup options missing from other low-end receivers. Perhaps one of the best features is the ability to flash the unit using a USB Thumbdrive, eliminating the need to connect the unit to a PC with a legacy serial cable.</big>Sometimes it takes a few minutes for autoroll to successfully find the key. After you flash the unit and hook it back up, simply be patient and wait up to 10 minutes before you are concerned there is a problem.Sometimes it takes a few minutes for channels to come in. After you flash the unit and hook it back up, simply be patient and wait up to 10 minutes before you are concerned there is a problem. If you just flashed the receiver you may note the signal is not available right away. Just wait a few minutes for the black screen to go away. Again, this is likely due to autoroll. You may have to reboot after several minutes (wait 10 minutes) for reception. == Manual Key Entry == * For KEYRIPPER Key00 is key86 (Lines 10 & 11) and key01 is key96 (Lines 20 & 21) 1) Press MENU, <SYSTEM SETTINGS> <USER OPTIONS> and turn Autoroll to "OFF" 2) Press EXIT 3) Press right arrow to <ENTERTAINMENT> and press 7890 4) A CODE option will appear, press OK 5) Press the right arrow until you get to CAS < NagraVision > 6) Press the down arrow to the sat line. Press right arrow until you get to your desired sat DISH < 01 01 00 > 7) key00 is active, highlight line number "10" then press the right arrow and start entering the keys (first 8 sets of digits)example: 1C 3A 29 13 61 5E C6 21 Now highlight line number "11" then press the right arrow and start entering the keys (second 8 sets of digits)example: C3 41 2A 31 5C 2B CD A1 8) If key01 was active, you would highlight line number "20" then press the right arrow and start entering the keys (first 8 sets of digits)example: 21 A4 C4 23 40 AC 1B 3A Now highlight line number "21" then press the right arrow and start entering the keys (second 8 sets of digits)example: 11 C2 41 A1 6D 2D 33 22 9) Press EXIT - Click "OK" on "YES" to save the changes NOTE: The example keys are just that, examples The active key is key00, Edit (Line 10) 1C 3A 29 13 61 5E C6 21(Line 11) C3 41 2A 31 5C 2B CD A1 If the active key was key01, We would have edited (Line 20) 21 A4 C4 23 40 AC 1B 3A(Line 21) 11 C2 41 A1 6D 2D 33 22 == Dish Network Settings == *! YOU MUST BE A PAID SUBSCRIBER. NEVER PROGRAM FOR CHANNELS YOU ARE NOT PAYING FOR! IT IS ILLEGAL TO PIRATE SATELLITE TELEVISION! Settings: LNB power ON LNB type OCS-DP LNB frequency 11250 Transponder 110=12224, 119=12239 22khz OFF Search option All Network search ON Diseqc 110=2, 119=1 Motor Disable Legacy switch OFF You have to set your antenna seting correctly for your dishpro twin OCS DP, diesq port 1 119, diesq port 2 110. Do not do blind scan on circular sats auto scan only. The first time setup only you will need to: Go into your Menu, then to System Settings. Now scroll down to User Options. Click on that and then turn on Channel Number by SID and Sort by SID. My first attempt put a “2” in front of every channel eg. 2400, not 400. Then Press the “SAT” button on your remote and then select the satellite provider name, this sinks up channel numbers. This was the easy fix for the channel # correction and only have to do the "SAT" button fix from now on after every update. EPG = channel guide listing downloaded. For best results to populate EPG. Try putting channel on 200 or 195 and let it sit for about 5 minutes and it should populate about 3 days. But it is impossible to get more then that. Because some providers do not do 7 day EPG.If you just flashed the receiver you may note the signal is not available right away. Just wait a few minutes for the black screen to go away. Again, this is likely due to the software at work. You may have to reboot after several minutes (wait 10 minutes) for reception.[[Category:Tangible Product]]